Before Remanufacturing                           After Remanufacturing

Remanufacturing Capabilities

Remanufacturing is a lower cost alternative to purchasing new equipment and an excellent option to purchasing used equipment of unknown quality. Mark Powers & Co., Inc. does more than just clean and test your equipment. We will tear your equipment down to its major components, test all components & bring those components back to factory specifications with factory and/or factory approved parts. In addition, we apply all factory mandated safety and performance updates to your equipment.

After disassembly and test / rebuild, Mark Powers & Co., Inc. will re-assemble your equipment, replacing any additional parts as needed. We will do a 100% system test and sanitize & cap all lines, pumps, valves, etc. We will also refinish your equipment to the point where in the case of fountain equipment, you can’t tell your refurbished equipment from a factory new one. And finally, we will pass your equipment through a thorough 10 point inspection process, insuring nothing was missed during the remanufacturing process.

Mark Powers & Co., Inc. provides quality remanufacturing for several major customers in the South East and we remanufacture 100’s of pieces of equipment every month. We understand the needs of today’s market challenges and would like to help with the cost savings opportunities of your fountain equipment. We have more than 20 years experience in the remanufacturing business.

Mark Powers & Co., Inc. can remanufacture all major makes and models of beverage equipment and valves. All remanufactured equipment is covered by a 90-day warranty.

Here are just a few of the remanufacturing services provided by Mark Powers & Co.

WUNDERBAR Barguns

5 Button Premix, 7 Button Premix, 8 Button Postmix, 10 Button Postmix, 12 Button Postmix, 14 Button Postmix

All Barguns are cleaned, tested, sanitized and repackaged. Most Barguns need few, if any parts, providing they are shipped to us complete. Barguns in warranty, in need of repair, are passed through to the manufacturer for repair at the manufacturer’s expense.

Counter Electric Fountains

We rebuild or replace all valves, clean & repaint hoods, re-texturize brushed stainless finishes, apply new factory approved graphics, replace all O-ring seals, replace any components that fail during test and install new key locks & keys.

In addition, we clean and sanitize the unit, cap all lines, do a 100% inspection, label with the appropriate serial number & asset number and box with the appropriate drain hose & accessories.

Drop-In Models

We rebuild or replace all valves, clean, pressure test, reseal & sanitize the cold plate, replace all tubing & insulation inside the tower, re-texturize brushed stainless finishes, apply new merchandiser graphics (when merchandiser is present), replace all O-ring seals, repair any ice bin water leaks, replace any components that fail during test and install new key locks & keys.

In addition, we clean and sanitize the unit, cap all lines, do a 100% inspection, label with the appropriate serial number & asset number and box with the appropriate drain kit and hose.

Ice/Beverage Units

We rebuild or replace all valves (specify pushbutton or sanitary lever), clean, pressure test, reseal & sanitize the cold plate, replace all tubing behind the cold plate as needed, re-texturize brushed stainless finishes, apply new merchandiser and side panel graphics (bulb replaced if needed), install new legs and support brackets as needed, replace all O-ring seals, repair any ice bin water leaks, replace any components that fail during test and install new key locks & keys.

In addition, we clean and sanitize the unit, cap all lines, do a 100% inspection, label with the appropriate serial number & asset number and box with the appropriate drain kits & drain hoses.

Carbonators

Check, disassemble & rebuild valves, install all new O-rings & gaskets, test Procon pump flow rate against factory specifications, test loaded carbonator pump motor current draw against factory specifications, repair or replace any components that fail test, check & fill both carbonator pump motor bearings with the correct oil, polish the tank, apply the correct decals to both the motor & the tank and perform a full system test on the re-assembled carbonator pump.

In addition, we hot sanitize the unit, cap all lines, do a 100% inspection, label with the appropriate serial number & asset number and box for shipment.

Regulators

Check, disassemble & rebuild the regulating element, replace all seals, clean regulator housing, test gauges for accuracy, replace gauges with correct range as needed and pressure test the entire unit.

In addition, we do a 100% inspection and package in a box designed to protect the regulator & gauges in shipping.

Mark Powers & Company, Inc.
P.O. Box 72 • 1821 Henry Street • Guntersville, AL 35976
Phone: (800) 633-2256 Fax: (800) 216-6606

E-Mail: orders@markpowers-and-company.com